Omega Owners Forum - bonnet release

fiend61 Senior Member Offline a car is not a car if it has cupholders Posts: 798 york Gender: Drives: 99-2.5L manual mfl, 00-2.5l auto f/l	bonnet release 15. May 2011 at 21:06 hi all got a problem with the lever that pops the bonnet, it is hanging off like someone has pulled too hard i havent taken it apart yet but some advice would be good would it have snapped needing new handle? or would fixings have broken that handle attatches to? advice would be good so can get bits beforehand tia
Back to top	IP Logged

Cotty

Newbie

Offline

Posts: 28
Darwen,Lancashire
Gender: male

Drives: 2000 Omega 2.5 V6CD

Re: bonnet release
Reply #1 - 15. May 2011 at 23:06

The same thing happened to me on my old 2.0l Roll Eyes

.
Luckily on mine the cable had popped out of its mechanism inside the lever and armed with a torch and a pair of pliers I soon had it back in working order Wink

.
Also make sure that the cable has'nt come loose anywhere under the bonnet as this will make it bloody hard to open,the first place to check would probably be where the cable is clipped to the plastic trim just above the back of the plenum.
Hope yours is an easy fix like mine Thumbs Up!

Back to top

IP Logged

fiend61

Senior Member

Offline

a car is not a car if
it has cupholders

Posts: 798
york
Gender: male

Drives: 99-2.5L manual mfl, 00-2.5l auto f/l

Re: bonnet release
Reply #2 - 16. May 2011 at 06:56

Quote:

Luckily on mine the cable had popped out of its mechanism inside the lever

no the cable hasnt come off it is still attatched to handle but the handle is hanging loose, you can still pull on the handle top and bottom to release bonnet, so either handle has snapped or where the handle fits onto has snapped, i will probally strip it down next weekend to have a look, i just wondered if this had happened to anyone else so i could have got bits before i started to strip it down ?

Back to top

IP Logged

Abiton

Omega Knight

Offline

Posts: 1064
Under Bonnet, nr Abingdon
Gender: male

Drives: Mk2 Golf, but the missus has a '96 2.0 'Select' woohoo!

Re: bonnet release
Reply #3 - 16. May 2011 at 07:54

fiend61 wrote on 16. May 2011 at 06:56:

Quote:

Luckily on mine the cable had popped out of its mechanism inside the lever

no the cable hasnt come off it is still attatched to handle but the handle is hanging loose, you can still pull on the handle top and bottom to release bonnet, so either handle has snapped or where the handle fits onto has snapped, i will probally strip it down next weekend to have a look, i just wondered if this had happened to anyone else so i could have got bits before i started to strip it down ?

Yep, more than a couple of times...

There's a (fixed, round) bit of plastic on the bit that falls out which is a sort of hinge pin IIRC, which just 'clips' into the fitting that's attached to the car. It's a horribly cheap-looking set-up for such an elegant car.

The good news is that it will probably just pop back in, once you get a torch and your head down there so you can see what you're doing.

Back to top

People are just about as happy as they have a mind to be.
Abraham Lincoln

IP Logged

This is the old site. Please use the new site.

This is the old site. Please use the new site.

www.omegaowners.com/forum/index.php.

This is the old site. Please use the new site.

	Welcome, Guest. Please Login