05. Apr 2026 at 17:49

	Welcome, Guest. Please Login

Shop

Help

Members

This is the old site. Please use the new site.

www.omegaowners.com/forum/index.php.

Omega Owners Forum › Omega Help › Omega General Help › Advice needed to give to garage

‹ Previous Topic | Next Topic ›

Pages: 1 2 3

Advice needed to give to garage (Read 2239 times)

tunnie Over Active Poster Offline Posts: 22520 London, W3 Gender: Drives: 2.2 CD (LPG'd) & BMW R1200 GS	Re: Advice needed to give to garage Reply #30 - 11. Feb 2011 at 22:33 take it back to the original garage and ask what the hell did you do with the anti-rattle springs!
Back to top	Do you break V6's as often as TheBoy? Then you need tunnie's towing services, recovery costs are just the humiliation of being towed by 2/3's of an engine IP Logged

I am a Daisy Junior Member Offline Posts: 136 Stonehoose Gender: Drives: 1998 Elite	Re: Advice needed to give to garage Reply #31 - 12. Feb 2011 at 01:29 Could the pins they talk of be the handbrake shoe pins, thus why they had to change wheel studs, thus why the clunk? Just a thought....
Back to top	IP Logged

Bent valve

Intermediate Member

Offline

Posts: 386

Drives: Omega 3Litre elite estate, Merc 190E

Re: Advice needed to give to garage
Reply #32 - 12. Feb 2011 at 05:41

I am a Daisy wrote on 12. Feb 2011 at 01:29:

Could the pins they talk of be the handbrake shoe pins, thus why they had to change wheel studs, thus why the clunk? Just a thought....

I think you might be right there, on my Merc if you fit the steel spare wheel you have to use the shorter wheel bolts supplied otherwise the extra length of the alloy wheel fixing bolt will wreck the handbrake mechanism.
Is it possible someone has been there before them and fitted an incorrect length wheel bolt to the rear Huh

I would check the length of all the wheel bolts just to be sure.

IP Logged

v6miggy

Senior Member

Offline

Posts: 890
Gender: male

Drives: 2000 2.5V6 CDX

Re: Advice needed to give to garage
Reply #33 - 12. Feb 2011 at 10:59

I am a Daisy wrote on 12. Feb 2011 at 01:29:

Could the pins they talk of be the handbrake shoe pins, thus why they had to change wheel studs, thus why the clunk? Just a thought....

This is definitely the pins they are talking about.
I went back and said about the anti rattle springs being missing and got looked at blankly Angry

The mechanic sat in the car with me and heard the clunking when I touched the foot brake. He said that once he readjusts the handbrake shoes then that should stop. I questioned the fact that it happens on footbrake not handbrake lever and again a vacant look.
Was told that the omega is a bad design but good car Cheesy

That is the usual response from someone that is incompetent Angry

It is booked to go back to them next Friday. So I will give them the chance.

As a point, after the anti rattle springs were fitted there was still a bit of play in the pads Questioning

ʎɐqǝ uo pɹɐoqʎǝʞ ɐ ʎnq ı ǝɯıʇ ʇsɐן ǝɥʇ sı sıɥʇ.

IP Logged

jonathanh

Senior Member

Offline

Posts: 859
coventry
Gender: male

Drives: 2.5V6 Manual Reflection

Re: Advice needed to give to garage
Reply #34 - 12. Feb 2011 at 16:28

where are you based? If anyone of us is close to you, someone should take a look.

The messages you are getting from your mechanic seem to say that he really does not know anything and is fobbing you off. the footbrake and handbrake mechanism are totally seperate. The former being hydraulic, disc/pad, the latter cable, drum and shoe.

now for my theory, could it be that the replacement cailper is from a facelift with vented discs and you have pre facelift - non vented disc?

good luck

parking near Birmingham airport for members with +250 posts. PM for info

IP Logged

Pages: 1 2 3

‹ Previous Topic | Next Topic ›

This is the old site. Please use the new site.

« Home

‹ Board

Top of this page